Welcome to the Club

Getting New Moms Adjusted to Mommyhood One Step at a Time

Group Home

Fun Ribbon Storage Ideas

Posted by on Nov. 15, 2012 at 4:08 PM
  • 6 Replies

On the hunt for a way to organize and store your ribbons??

Thanks to frugal friend Kathy in Connecticut for sharing this creative Ribbon Storage Idea!

I’m always picking up fun new ribbons to make Ribbon Hair Clips, Crafty Clipboards or whatever other crafts I’m working on, so I absolutely love this fun way to store them!

What You’ll Need:

  • A thick plastic container with a lid {or a sturdy cardboard box}
  • 5/16” wooden dowels
  • A 5/16” drill bit and drill
  • Either wood glue or hot glue… or both. {Tip from Kathy: I didn’t have the patience to let the wood glue set before loading the dowels up, so I also glued around the outside of the dowel with hot glue.}
  • As many ¾ inch, wooden, screw-hole plugs as dowels {alternatively, Tinker Toys may fit these dowels. I think they would be adorable on both ends but glued on only ONE end.}

What You’ll Do:

  • Using your 5/16” drill bit, drill holes in the wooden screw-hole plugs but not all the way through. Put some glue in the hole and attach your dowel. It should be a very tight fit. You can sand the dowel a little to make it fit if necessary {but it shouldn’t be ~ use some muscle!}. ;)
  • While your glue dries, measure a dowel to fit your container’s width so that they extend about one inch or so beyond the outside of the box.
  • Cut all dowels to your measurement. {they’re small enough that you can simply use a serrated knife to score around the dowel and then just snap it off}
  • Measure and mark the spacing of the holes for your dowels on the box with a Sharpie. On each side of the box, the holes should be approximately 2.5” from the short end of the box, approximately 2.5-3” down into the depth of the box, and a minimum of 5 inches away from each other going down the length of the box. Use your ribbon spools to gauge the exact distance you would like them placed, just be sure that they match up on the opposite side. Depending on the size of your box, mark as many holes as will fit dowels. {I used three dowels}
  • Using your 5/16” drill bit, drill the holes according to your marks.
  • When the glue is dry on your dowels, push the dowel through a hole in the box and load ‘em up with ribbon spools! When full, put the dowel through the second, corresponding hole.

Ribbon ends can be secured to the rest of the spool with either a small tab of tape or a sewing pin.



by on Nov. 15, 2012 at 4:08 PM
Add your quick reply below:
You must be a member to reply to this post.
Replies (1-6):
Stevensmomma
by on Nov. 15, 2012 at 4:53 PM

good idea

suziejax
by Suzie on Nov. 15, 2012 at 7:07 PM

like it!!!!!!!!!

AzariahsMother
by on Nov. 15, 2012 at 8:48 PM

Neat

jbyrd898
by Jessica on Nov. 16, 2012 at 10:05 AM

good idea

yvonne37
by Yvonne on Nov. 16, 2012 at 11:57 AM

 thats a good idea and then you can put the lid on.

allyn9
by Carey on Nov. 16, 2012 at 6:37 PM

Cute idea, but there is no way I would ever have that much ribbon around the house to need something like that. 

Add your quick reply below:
You must be a member to reply to this post.
Join the Meeting Place for Moms!
Talk to other moms, share advice, and have fun!

(minimum 6 characters)

Advertisement